Call us now + 91 982 509 5736, + 91 982 507 2639

GAL - SL (Epoxy Self Levelling)

GAL -SL is based on high performance epoxy resin & curing agents. GAL - SL is a three-component system, Containing of resin, curing agent and carefully graded iron free fillers. Product is self-levelling to achieve excellent gloss, attractive, hygienic and very hardwearing & chemical resistant finish.

FEATURES

  • Being smooth, joint less and monolithic surface it is very easy to clean and to make it dust free.
  • Product is based on high performance epoxy resin & curing agent system. The flooring system has excellent overall chemical resistance at ambient temperature.
  • A carefully selected and graded high wearing aggregate gives very strong floor toppings to withstand normal foot and light vehicular traffic.
    System is available in many attractive colours.

USES

GAL -SL is highly recommended, for use, for extremely hygienic condition, chemical resistant and dust free areas like:

  • Automobile Industries.
  • Pharmaceuticals & Aesthetic areas
  • Food Processing areas
  • Bottling plants
  • Electronics industries
  • Hospital Operation Theatres
  • Chemical plants

SPECIFICATION

Application Brush, Roller
Film Thickness 1mm, 2mm , 3mm
Coverage 3.35 to 3.50 kg/M2 (Approx.) for 2mm thickness
Application Notch Trowel & Spike Roller
Curing Initial-6-7 Hrs
  Full 7 days
Finish Gloss
Mixing Ratio As directed on Packing
Colours Grey, Green, Red, White or as required

SURFACE PREPARATION

For Successful performance of GAL - SL or any other flooring system can achieve only after proper surface preparation. It is the prime requirement that surface must correctly prepared before application.

  • New concrete surface must be cured for 28 days
  • Surface must be free from any oils, grease, loose partials, curing aid chemicals, previously applied coating etc…
  • Surface must be fully dry.
  • For old surface, all cracks, cavities should be repaired with GAL Epoxy Putty.
  • This is a very thin topping so cannot level any irregularities of levels of the original sub-base. Therefore, it is most important to make original surface in line & level, before application of GAL - SL.

APPLICATION

(PRIMER COAT)
Apply one coat of GAL - SL primer on properly prepared surface by brush and allow it to dry.

SELF LEVEL TOPPLING

First mix the resin part A, thoroughly with slow speed mixer until uniform colour is achieved. Then add curing agent part B and mix again with mixer (@less then 80 rpm). After that add filler par C and mix with mixer until a homogeneous, lumps free mass is achieved (@less then 80 rpm). Then, pour it on primed surface and work with notched trowel to required thickness and apply spike roller to remove air. Proper mixing is the key factor to get uniform color and smooth surface.

STORAGE

All the components Resin, Hardener & Filler must be kept in cool, dry place and in covered shed.

HEALTH & SAFETY

It is advisable to wear protective wears at the time of use of GAL - SL and all other GAL brand products. In case of contact with eyes and skin, wash with plenty of water and consult a doctor.

This information, given above in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use is beyond our control.

Typical properties:  For GAL - SL Material

Compressive Strength 50 -55 N/MM2
Flexural Strength 35 N/MM2
Adhesion to Concrete 3.00 N/MM2
Tensile Strength 18N /MM2
Water Absorption at 270C @24 Hr. 0.20%
Elongation at break 7.5%
Rockwell hardness on R Scale 80
Charpy impact value 73 Joule / meter

Note: This leaflet is for reference and dose not give description of goods.

Visit our Gayatri Pariwar (www.awgp.org)
Home | Product Range | Our Services | Treatment Area | About Us | Why Us | Technical Data | Our Clients | Contact Us
Copyright © Gayatri Anticorrosive Lining 2011.
Follow Us :   Facebook Linkedin
Webdesign By Megh Technologies